Compatible
WE03X29897 WE12M29 Dryer Belt Drive fits for GE Whirlpool Kenmore AP7012633 | Also for Hotpoint, Replaces…
| Part type | Dryer Drive Belt |
|---|---|
| Made by | PartsBroz |
| Genuine or compatible | Compatible equivalent (made by another company) |
| Main part number | WE03X29897 |
| Also listed as | WE12M29, AP7012633, PS16542496, WE12X21574, WE12M0022, WE12M22, WE12M33, WE21M29 |
| Model numbers named in the listing | GTD33EASK0WW, GTD42EASJ2WW, GTDP490ED0WS, GTDP490ED5WS, DBXR463ED2WW, GTD42GASJ2WW, GTD42EASJ0WW, GTD45EASJ2WS, GTD45GASJ2WS, HTDX100EM8WW |
What it fixes
The long belt that loops around the drum and is turned by the motor, so the drum tumbles. Fit it if you see:
- The motor runs but the drum does not turn
- A thumping or flapping noise as the drum spins
- A smell of burning rubber
- The belt looks frayed, stretched or has snapped
Will it fit your appliance?
This is a compatible equivalent made by another company, so fit depends on the model. The details below come from the seller’s own listing and are shown so you can compare them with your rating plate. Always confirm on the Amazon page before you buy.
Model numbers named in the listing: GTD33EASK0WW, GTD42EASJ2WW, GTDP490ED0WS, GTDP490ED5WS, DBXR463ED2WW, GTD42GASJ2WW, GTD42EASJ0WW, GTD45EASJ2WS, GTD45GASJ2WS, HTDX100EM8WW
From the seller’s listing:
- Drive Belt WE03X29897 fits for GE Dryer Belt Replacement, is an exact replacement for WE12M29, WE12M22, PS16542496, WE12M33, AP7012633, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE03X29897-30PK, WE120122, WE12M0022.
- WE12M29 Dryer Belt is a 89.5 inch dryer belt and is compatible with General Electric dryer belt, Whirlpool, Kenmore, and Hotpoint dryer belt, ensuring a proper fit and reliable performance.
Other part numbers it is listed as replacing: WE12M29, AP7012633, PS16542496, WE12X21574, WE12M0022, WE12M22, WE12M33, WE21M29. Matching one of these to the number on your old part is the most reliable check.
Check your model number first. It is on the rating plate — usually inside the door frame, on the back or side panel, or inside the appliance. Parts that look identical often differ by model, so match the number to the listing before you order.
How to fit it
- Unplug the dryer
- Remove the top, front or back panel as needed for your model
- Release the tension on the idler pulley and remove the old belt
- Loop the new belt around the drum with the ribbed side against the drum, then around the idler and the motor pulley
- Check the belt sits straight, refit the panels and test
Difficulty: Moderate. Typical time: 45 to 90 minutes. Read the full dryer drive belt guide, including checks to run before you buy.
Safety. Unplug the dryer before you start (and switch off the breaker if it is hard-wired). A blocked vent is a fire risk, so always clear the cause of any overheating.
Other dryer drive belt listings
Genuine made by Hotpoint / GE Compatible made by another company to fit
